Sponsored Links

PS4 News on Facebook! PS4 News on Twitter! PS4 News on YouTube! PS4 News RSS Feed!
Sponsored Links
Sponsored Links
Home PS4 News - Latest PlayStation 4 and PS3 News

PSGroove USB Boards and DIY Teensy Schematics Detailed

Sponsored Links
239w ago - With the release of PSGroove opensource PS JailBreak exploit for PS3, many are having trouble sourcing the required Teensy++, AT90USBKEY2 or AT90USB162 boards.

That said, today PS3JailBreak.com (linked above) has shared schematics for the Teensy so that users can build their own if they wish.

As always, click on the picture below to enlarge it folks.

Finally, those who aren't into DIY solutions may also wish to look into either the AT90 USB thanks to Fuddster or the BlackcatUSB Flash Memory Programmer (from version 1.2 on) which uses the same microcontroller (AT90USB162) as confirmed by chesteruhi. More on that soon, including a video!

To quote: "The full schematics are available below (1.0 are on the top 2.0 are on the bottom)."

PSGroove USB Boards and DIY Teensy Schematics Detailed

Stay tuned for more PS3 Hacks and PS3 CFW news, follow us on Twitter, Facebook and drop by the PS3 Hacks and PS3 Custom Firmware Forums for the latest PlayStation 3 scene and PlayStation 4 scene updates and fresh homebrew PS3 Downloads. Enjoy!

Comments 47

+ Reply to Thread

#7 - RolF2 - 239w ago
RolF2's Avatar
bootloader is preinstalled by atmel , no problems here

#6 - ramx2 - 239w ago
ramx2's Avatar
Electronics experts, if we print and build the teensy pcb do i need to flash the bootloader or its preinstalled ? I know haveI to load the hex later on, but will the pcb fuction as it should ?

Please I need to know before building it, thanks...

#5 - jd200 - 239w ago
jd200's Avatar
is there a parts list for these? then we know what to buy and order to make it. i'm good at soldering but not good at understanding what to order by just looking at the picture.

#4 - caravela - 239w ago
caravela's Avatar

what kind of capacitor and voltage should i buy ? do i really need a BAT54C or can i use something else ?


#3 - hakz - 239w ago
hakz's Avatar
Damn it's been about 2 years since I did work on a breadboard in uni, can't remember a lot.

#2 - Keeper75 - 239w ago
Keeper75's Avatar
There's no need to cut anything from the schematics - if you want to build one of them, just make the teensy one at the top left - it's the easiest one (and probably the cheapest one too).

#1 - iCEQB - 239w ago
iCEQB's Avatar
Someone capable of cutting out the not needed stuff from these shematics?

The USB Port, Controller, LEDs, Crystal, Resistors should be enough ?

What about the button thise things have? Those are for programming mode right?

This is a good schematic from joohan: http://www.ps4news.com/forums/attachment.php?attachmentid=21200

USB Dongle for 64pin Atmels, with integrated USB connector, now also for 32pin

I made a quick & dirty usb dongle board for running psgroove, so if anyone find it useful then here you go.. Made with freeware Eagle 5.9

The board should be pretty easy to manufacture since only one layer is required(with one jumper, the second layer in the brd file is only GND and can be left out).

The BOM count is minimal, with no "hard to find" parts. I think all 64pin AVR's with USB should work, but I have only tried the AT90USB1287

Tested with psgroove and the default "USER" layout

IC1 AT90USB1287 or similar
C1,C2 15p(10p-30p should be ok)
C3 1u(from atmel datasheet)
C4 1u(not a critical value, can live without it)
C5 0.1u(not a critical value)
LED1,LED2 SMD 1206
Q1 16Mhz OR 8Mhz
R1,R2 500 (about)
R3,R4 27 (about)
R5 2k (anything in 100-100k range)

EDIT: The chips comes with an preprogrammed USB bootloader, use FLIP from atmel.com for programming
To enter bootloader mode, short the 2pin header, insert the dongle to the PC, force a reset(by shorting the reset TP to ground with a small screwdriver).
After programming remove the short on the header

To test the dongle after programming, insert into a pc and led2 should turn on. If it doesn't then hard force a reset(..by shorting the reset TP to ground..) I had to do this on 1 out of 3 tested pc's. You should now get a USB connection with ID aaaa:5555

Advertising - Affiliates - Contact Us - PS4 Downloads - PS4 Forums - Privacy Statement - Site Rules - Top - © 2015 PlayStation 4 News