PS4 News on Facebook! PS4 News on Twitter! PS4 News on YouTube! PS4 News RSS Feed!

Closed Thread
Page 3 of 3 FirstFirst ... 23

 
 
  1. #21
    Join Date
    May 2013
    Posts
    15
    tried that version 2 m8, no work either.. what i have installed is just cfw either rebug 4.41 with multiman 4.40 or Rogero 4.40 version 1.03 with multiman 4.30 and 4.40 also tried Rogero_Manager_v8.2 with rogero.. is that enough to get ps3 up and running or am i forgeting to install something else ?

    is it worth downgrading back to OFW 3.55 then upgrading again to rebug 4.41 could my firmware be corrupt ? sometimes when i turn ps3 on it says files corrupt but when i let it go through fixing files it crashes at 19 % and wont finish repairing files either from xmb or safe mode .. thanx for your patience guys

    also if i have to go to 3.55 can i do it over rebug 4.41 ? cheers
    Last edited by karpof; 06-08-2013 at 03:13 PM Reason: Automerged Doublepost

  2. #22
    Hello Bud, if its possible swap out your drive that's in that ps3, with a small drive just for working with, trust me when I say it helps not needing to format a drive when the ps3 has crashed and its lost the drive inside.

    In a nut shell you need to force manufacturing_updater_for_reset.self into the ps3 without trying to use the pup that the file came in, to reset the bd if that make sense.

    The instructions say you need your Ps3 on a working 3.55 firmware, but the ps3 I did was also on 4.41. I used the E3 to do in short this below.

    Remarry guide for 3.55 firmware from: http://www.ps4news.com/forums/ps3-ha...tml#post411024

    Related guide: http://www.ps4news.com/ps3-hacks-jai...ther-consoles/

    1. Have the console on a working 3.55 firmware

    2. Download the Remarry files (remarry-3.55.rar) and unpack to root of USM Mass Storage device. The following line is already changed from 1 to 0:

    [Register or Login to view code]

    This will make sure the drive init PUP is not installed, thus preventing RLOD because of syscon hashes on downgraded consoles.

    3. Download official firmware <=3.30 as drive init PUP and put it root of USB Mass Storage device

    Content of USB Mass Storage device should be thus be:

    [Register or Login to view code]

    4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.

    5. Put the created USB Mass Storage device from step 3 into port 0 (closest to the reader) and run.

    Drive Init Executing means it is starting the remarry process
    Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.

    6. After you run the initial remarry process, do not take it out of factory service mode.

    7. Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)

    8. Then you can take it out of factory service mode.

    9. Launch as normal.

    [Register or Login to view code]

    Please Note if it displays this, Drive Init Executing means it is starting the remarry process. Drive Init Failed with big pink letters 'NG' (No Good!) means the process failed. Most likely solved by fixing the communication issue with the drive.

    Try 1st as it said this ti me and it still worked, go figure, lol

    Hope some, if not all helps.

  3. #23
    Join Date
    Jun 2013
    Posts
    342
    Install a CFW (I suggest Rebug or Rogero 4.XX)
    Use multiMAN to place games on.
    Use homebrew such as emulators.

    The most important thing of all, have fun.

  4. #24
    Join Date
    May 2013
    Posts
    15

    daveshooter and JeoWay

    hi dave.

    4. Put the service mode JIG/dongle/PSGrade into port 0 (closest to the reader) and get into factory service mode.

    I don't have a JIG/dongle and my BD dont work to Put a BD movie disc in and run it on the PS3. (This restores your DRL files!)

    and jeoway: Multiman crashes, thats my prob. what emulaors will work ?

  5. #25
    Sorry late reply, just to say I don't think you can fix your ps3 without some form of hardware.

  6. #26
    Join Date
    Oct 2010
    Posts
    178
    When you load a game from Multiman, it always gets you back to XMB... then you have to scroll up in the Game menu and you'll see a disc icon ...as if you were inserted a real disc... you then select that disc icon and the game should start!

    You are almost there... good luck!

    Happy gaming!

 
Closed Thread
Page 3 of 3 FirstFirst ... 23

 
 
 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •