PS4 News on Facebook! PS4 News on Twitter! PS4 News on YouTube! PS4 News RSS Feed!

+ Reply to Thread
Page 3 of 8 FirstFirst ... 234 ... LastLast

 
 
  1. #21
    heat is the main reason of YLOD. So the aim of this is quite obvious

  2. #22
    Join Date
    Apr 2009
    Posts
    452
    Am I doing something wrong or is it not functioning properly on Rebug Rex 4.30.2? I select the automatic payload and exit so then it goes to sleep. I start it up and it is on the payload, by default it turns on the fan while the default setting would have it pretty much off until around 60C. But unless I enter the actual program again it does not increase speeds, it remains at a low setting. Entering the program to get it functioning properly is not an option since exiting it causes it to put the PS3 to sleep again.

    Edit - It seems to work fine from a cold boot though.

    Edit 2 - Well it seems I have no idea what I'm doing because now that I've re-enable error messages it's saying what's happening is an improper shutdown, and it doesn't work off of a cold boot. Last time must have been a coincidence.

    I don't know why it's not functioning, whether it's a problem in general or if I've done something wrong. If anyone has any ideas please post them.

    Edit 3 - Good news, I think I finally figured out what the unknown factor was. Every time I run the Rebug Toolkit beforehand it no longer crashes. I've tried it 4 times in a row, and it's 4/4. Any time I did not run the Toolkit first, it crashed. It's very unlikely to happen that many times in a row if it was a coincidence.

    I have no idea why this is, but I hope the author fixes this soon. It's a very important program, it makes the PS3 loud but is well worth it. My extremely well cleaned and maintained PS3 (which I use AS5 on) would approach 70C on the Cell and 68C on the RSX while idle. That's insanity, for comparison my Xeon W3530 at 4GHz idles at 40C and tends to max out at 65ish in programs.

    That's a relatively large overclock pushing it beyond its normal thermal limit or it would have lower temperatures. No wonder the solder holding the Cell and RSX degrade and break, they probably approach 100C under full stress. Now my PS3's temps are 63-64C/59-60C at all times including under load, it just increases the fan speed as needed to keep the temps around there it seems.

    Edit 4 - After further testing it seems it runs without crashing if run after Multiman as well. This leads me to believe so long as a program is run before it, it won't crash.

    Some bad news though, having it run it's auto setting, the payload, seems to interfere with normal function. Whenever I have it set to the payload I get static in games, even the sound quality in general when it's not static seems degraded. Having a manual constant setting resolves this but is not ideal.

    The games I tested were Blazblue Continuum Shift Extend and Persona 4 Arena. Both have very obvious static in the music when the payload is running. I hope the author can solve these problems.
    Last edited by Neo Cyrus; 05-21-2013 at 08:37 PM Reason: Automerged Doublepost

  3. #23
    can any one help after installing this i didn't change any settings basically i was just having a look what it did and unistalled it but after uninstall after about 10 mins of playing my ps3 i have started getting the error that it is too hot and needs to be shut off to cool which i have never had this before so any help would be appreciated.

  4. #24
    Install fan utility 1.7
    Run the program
    Go to Siscom mode
    Leave the program pressing triangle in Siscom mode.
    Delete the program in XMB
    In recovery mode Restore File System and Rebuild Data base
    Never use it again

  5. #25
    thanks for the info but looks like i'm screwed, not got the genuine sony controller no more so when i get to plug in controller and press ps button that's as far as i can get but thanks once again.

  6. #26
    Join Date
    Jun 2009
    Posts
    530
    done setting on my side, although it lags on games and highly noticeable.

    My old temps without FCU:

    CPU:70-77celcius (idle to while gaming)
    GPU: 57-63celcius (idle to while gaming)

    With FCU running in custom payload setting:

    CPU: 57-68celcius (idle to while gaming)
    GPU: 51-53celcius (idle to while gaming)

    setting from 0x80 - 0xA5

    Well that's the big difference between using FCU and a normal SYSCON fan control.

  7. #27
    Join Date
    Jun 2013
    Posts
    342
    Put your ps3 in a freezer. It works. Until its frozen

  8. #28
    It's a great app, but I hope my fan won't die if I use this

  9. #29
    Join Date
    Sep 2010
    Posts
    847
    If you are getting above 70 on idle you should change heatsink paste on cpu or you are in cooking range , be advised that cpu have 2 stage construction

  10. #30
    Join Date
    Jun 2009
    Posts
    530
    not really, I did replace the compunds both beneath IHS and above IHS, there are little changes on temperatures after i replaced it, although on 2c difference, so I cant see anything wrong with it until this FCU came, now my PS3 is cool like 51celcius and 48celcius after I set it to 0xC5, kinda loud fan noise but I dont care since I play with headphones, also its better to get the fan wrecked than having a YLOD PS3 which is much more expensive than replacing a new fan.

 
+ Reply to Thread
Page 3 of 8 FirstFirst ... 234 ... LastLast

 
 
 

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •